Published: June 29, 2026 Source: Huatao Group Roller Department
In a Continuous Galvanizing Line (CGL), the zinc pot assembly represents one of the most hostile processing environments in the steel industry. Submerged completely within molten zinc at temperatures ranging from 450°C to 480°C, the sink roll (or pot roll) is forced to operate under constant thermal shock, severe chemical corrosion, and heavy mechanical wear.
Because the sink roll directly guides high-tension steel strip through the molten zinc liquid, any surface degradation or accumulation of zinc dross will instantly print severe micro-indentations, scratches, or coating irregularities onto the steel sheet. For steel manufacturers supplying automotive-grade or home-appliance-grade galvanized sheets, maximizing sink roll lifespan while preventing surface defects is a critical operational priority.
Why do conventional rollers fail prematurely inside a galvanizing pot? Plant engineers must address two interconnected destructive mechanics:
Intermetallic Chemical Attack: Molten zinc is highly aggressive toward iron. At 460°C, it continuously reacts with standard steel roller cores, dissolving the iron molecules and forming brittle iron-zinc intermetallic compounds. This causes rapid surface pitting and structural erosion.
Zinc Dross Build-up: As iron dissolves into the bath, it reacts with zinc and aluminum to form microscopic solid particles known as top dross or bottom dross. These hard crystals adhere to the sink roll face, creating a rough, sand-paper-like texture that ruins the strip's surface profile.
To counteract these aggressive mechanisms and confidently extend the campaign life of the zinc pot system, Huatao Group manufactures custom sink rolls optimized around three technical disciplines:
We construct our sink roll shells from premium, specialized heat-resistant stainless steels and cobalt/nickel-base superalloys (such as 316L or proprietary low-iron stainless formulations). These alloys exhibit exceptional structural stability at elevated temperatures, maintaining precise geometric profiles under high strip tension without thermal bowing or creep deformation.
The ultimate line of defense against liquid zinc corrosion is our surface engineering. Huatao Group applies high-density WC-Co (Tungsten Carbide-Cobalt) or Cr_3C_2-NiCr (Chromium Carbide) cermet coatings using cutting-edge HVOF (High-Velocity Oxygen Fuel) thermal spraying technology.
Porosity Control: The coating porosity is compressed to ≤1%, completely sealing off the underlying steel core from liquid zinc penetration.
Anti-Dross Properties: The inert ceramic surface resists chemical bonding with iron-zinc dross crystals, allowing the roller to repel dross accretion during long runs.
To facilitate the continuous escape of entrapped dross particles from the contact zone between the steel strip and the roll face, Huatao Group mills custom spiral or helical grooves onto the roller surface. This specialized geometry acts as a centrifugal pump, utilizing the roller's rotation to continuously flush dross out into the main bath area, preventing microscopic imprints on the sheet.
| Parameter | Standard CGL Pot Roller | Huatao Premium HVOF Sink Roll |
|---|---|---|
| Core Shell Material | Standard Cast Stainless Steel | Vacuum Degassed, Low-Iron Heat-Resistant Alloy |
| Surface Treatment | None / Basic Hard Chrome | HVOF Thermal Sprayed WC-Co / Ceramic Matrix |
| Surface Hardness | 250 – 300 HBW | ≥950HV (Ultra-Hard Cermet Layer) |
| Corrosion Resistance | Moderate (Susceptible to pitting) | Excellent (Inert to liquid Zn, Al, and GL baths) |
| Typical Campaign Life | 7 – 10 days before grinding | 20 – 35 days continuous running (Application dependent) |
| Application Scope | General building materials | Automotive exposed panels & High-end home appliances |
A premium sink roll achieves its peak efficiency when integrated properly with matching stabilizer rolls (correcting rolls) and high-precision self-lubricating ceramic bearings. Huatao Group provides fully integrated "Zinc Pot Three-Roll System" kits custom-dimensioned as direct drop-in upgrades for global galvanizing plants. By extending maintenance intervals, we help you reduce hazardous pot-hardware changes, cut labor costs, and achieve a stable, premium-finish product line.
Request an Engineering Blueprint Review & Price Quotation:
Contact: Tony Liu
Email: sale08@huataogroup.com
WhatsApp: +86 13383112591
can not be empty
can not be empty
HUATAO GROUP - ROLLS
Address: No.298 Zhonghua North Street, Shijiazhuang 050000 China.
Tel: +86 0311 80690567
Email: sale08@huataogroup.com
WhatsApp & WeChat : +86 13383112591